Pendulum Impact Test
(EPTIS ID 591285 / Certificate of Accreditation nº AP-2654)
Click on the link below and download your Application Form:
Send the completed form to email@example.com
The E-mail Subject MUST contain the name of the PEP + Company name (Example: Pendulum Impact Test - Company)
After sending, wait for contact from our company via E-mail.
*If more than one company is participating, each of them will have to have an individual application.
If you still have any difficulty, contact us (55 41 4106-8010), and we will help you in the best way and ensure that your registration is successful!
The Pendulum impact test proficiency scheme consists of determining the height of the pendulum that the test item reaches failure, with any accredited laboratories or in the accreditation process being eligible to participate.
The pendulum impact test shall be performed individually on the test items received, adding to each item a predetermined height range on the pendulum until the height at which the piece will reach failure. The participant should proceed as in their practice routine.
The participant must have a pendulum, according to IEC 60068-2-75 - Item 5 Impact Hammer Pendulum of item 5.1.2.
For quantitative tests, Qualabor follows the following order for assigned value choice priority:
1) Robust Z' – Score with the robust average - In the area of testing there are no clear levels of quality between laboratories for the same test, this way is hard to determine a laboratory with recognition of a higher quality that is accepted by the other participants. The use of an assigned value from a group consensus is the most applicable, In this case, determined by the result's robust average, which does not require an independent treatment of outliers. To be able to use group consensus with minimal robustness is necessary a group with 4 or more participants. The choice of the z'-score method is due to the same being of greater acceptance by the clients and also by difficulties in calculating uncertainty of measurement by the participants, which is not sensitive to this method.
02) Normalized error with a reference value – When it is not possible to have a group with more than 3 participants, the assigned value utilized will be a reference value, previously validated with participants and always that exists, this value will be taken through an accredited laboratory, and in this case is given priority to the normalized error because the denominator of z' score is the program standard deviation which has low robustness because there are few participants.
The activities of Qualabor as a proficiency testing provider are done with impartiality and are structured and managed to guarantee that, Qualabor also compromises that commercial, financial, and other types of pressure will not compromise Qualabors' impartiality. It is assurance through the acknowledgment and agreement term, signed by Qualabor collaborators, who affect the quality of proficiency testing.
This PT is part of Qualabor's accredited scope.
(Certificate Number: AP-2654, ANSI National Accreditation Board - USA)
Qualabor's QMS is implemented and effectively maintained according ISO/IEC 17043.
EPTIS helps you find a suitable proficiency testing (PT) scheme for your laboratory (a PT scheme is a coherent series of single rounds). For a large number of schemes we have produced data sheets and collected them in the EPTIS database. What is not included in the database is topical information on next PT rounds. When is the next round, and what is the matrix material this time? This information is too dynamic as to be included in the database. But you can find such details for a selection of schemes in our PT calendar.
At present, a listing on the database is only open to PT providers from countries that are covered by our so-called coordinators. They check the plausibility of the data sheet submissions and decide on their publication. They speak the language and are ideally familiar with local PT providers and cultural peculiarities. This helps to safeguard a reasonable level of database quality. There is no cost for PT providers who follow this basic mechanism.
Qualabor register every finished PTs on EPTIS (European Proficiency Testing Information System) database, informing its technical characteristics to anyone who shows interest.
Registrations should be made through the Inscription Form at the tab “Inscriptions”
As the participants minimum number is met, the PT is confirmed
The PT’s samples will be send to the participants in a sequential or simultaneous manner in accordance with the PT
June to December
* This schedule can be modified before the round confirmation for Qualabor, client or regulatory bodies’ necessity.
Investment*: 985 USD/EUR per registration.
Payment Method: Via bank transfer.
For more information: firstname.lastname@example.org or 41 4106-8010.
In case of a complaint or appeal of proficiency program results, the following steps should be followed:
- The participant should send Qualabor by email the complaint or appeal through email@example.com;
- When the email gets to Qualabor, the participant will get notified that their complaint/appeal was received and may request information about its progress whenever necessary.
- The complaint/appeal will be evaluated by Qualabor, and any corrections or corrective actions needed will be decided and implemented.
- After that, a person authorized by Qualabor that was not involved before in the process will send a response to the participant about the process result.
- The participant may contest the decision if it was not satisfactory.